Most repairs fail because the cause is never identified.
We detect, measure, and correct the failure — so it doesn't happen again.
Find the Cause First. — This is not a surface correction — it's a permanent failure correction strategy.
Request Assessment View Failure AnalysisSlabWorx is a Concrete Failure Intelligence System designed to identify, measure, and correct concrete deterioration before it becomes a major problem. | Fixed Once. Backed Forever.
Concrete in Vermont and New England is exposed to some of the harshest conditions in the country: freeze–thaw cycling, moisture saturation, soil movement, chloride exposure. Most repairs fail because they treat the surface—not the cause. In our field work and documented case analysis, failure consistently begins with moisture intrusion and structural movement. If those conditions aren't corrected, the repair will fail again. Over $1 million in unnecessary scope has been identified and eliminated across our project history by finding the cause first.
Moisture is the primary catalyst of deterioration
Every project is evaluated using a four-part performance model. Failure occurs when these systems are misaligned. Our process identifies and corrects each one before repair begins.
The Primary Driver of Deterioration
Capillary pore infiltration, 9% volumetric freeze expansion, progressive matrix destruction. The failure chain begins here — not at the surface.
ACI 201.2RCrack Propagation & Settlement
Differential settlement, frost heave, and subgrade instability generate tensile stress. Vermont frost depth: 48". Every cycle advances failure.
ACI 360R · ICRI 310.1Stress Concentration at Weak Points
Applied load combined with existing damage creates stress concentrations that exceed tensile capacity. Crack classification per ACI 224R determines repair category.
ACI 224R · ACI 318The Bond Integrity Layer
ICRI 310.2 defines nine CSP standards. Bond failure at the interface is the most common — and most avoidable — cause of premature repair failure in Vermont.
ICRI 310.2 · ACI 546Failure occurs when these systems are misaligned. Our process identifies and corrects each one before any Failure Correction Strategy begins.
Small issues escalate when left unaddressed. Cracks expand. Moisture weakens the slab. Surface damage becomes structural. What starts as a minor risk can quickly become a major cost. Identifying the problem early is the most cost-effective solution.
Begin Failure DetectionInitial Failure Signal
Hairline cracking, surface scaling, minor moisture migration. Easily corrected with targeted Failure Detection and early intervention.
Low RiskActive Moisture Intrusion
Cracks widen. Water establishes pathways. Freeze-thaw cycling accelerates internal expansion. Subgrade begins saturating.
Moderate RiskStructural Deterioration
Settlement detected. Void formation beneath slab. Trip hazard liability measurable at ¼"+. Surface repair is no longer an adequate response.
High RiskFull System Failure
Major replacement required. Liability exposure significant. Total project cost is 4–10× what early-stage correction would have been.
CriticalFive stages. Every project. Diagnostic data drives every decision — scope is determined by what we find, not what we assume. Find the cause first. Then correct it permanently.
Stage 01
Drone survey, visual analysis, and thermal imaging. Full site documentation before any Failure Detection equipment deploys.
Stage 02
AssetGuard™ system, GPR analysis, subsurface condition mapping. The data layer most contractors skip entirely.
Stage 03
Root cause determination, not symptom treatment. All four systems evaluated. ACI/ASTM/ICRI-referenced documentation produced.
Stage 04
Engineered solution addressing the actual failure mode. Cold-climate material specification. Not a generic surface treatment.
Stage 05
Post-repair documentation, performance monitoring, and our backed guarantee. Fixed once. Backed forever.
Every service begins with assessment. We don't recommend a Failure Correction Strategy before we understand what's failing and why.
Identify and correct elevation changes and surface hazards that create liability risk. GPS-mapped documentation to ¼" measurement tolerance. Legally defensible records for municipal, commercial, and institutional properties.
Request AssessmentDetermine root causes of cracking, spalling, and structural deterioration. Full four-system evaluation. ACI/ASTM/ICRI-referenced reporting that functions as an engineered document — not a contractor estimate.
Request AssessmentEvaluate water pathways, drainage issues, and saturation conditions driving failure. Ground penetrating radar (GPR) combined with thermal imaging provides a complete subsurface moisture pathway map — locating the source, not just the symptom.
Request AssessmentStabilize active cracks based on movement classification—not surface appearance. Engineered Failure Correction Strategy with cold-climate material specification. ACI 224R crack classification determines repair category before any material selection.
Request AssessmentRepair failed overlays and bonding issues caused by improper surface preparation. ICRI 310.2-compliant substrate preparation, pull-off testing per ASTM C1583. We specify preparation methods to standard and verify — because the bond is everything.
Request Assessment“Concrete doesn't fail randomly. It fails when the cause is missed.”
We don't start with repair. We start with identifying why the concrete failed. Find the cause first — then correct it permanently.
The SlabWorx Standard
What Failure Detection intelligence delivers that standard contracting cannot. This is not a patch — it's a permanent failure correction strategy. We don't patch symptoms — we correct failures.
| Capability | SlabWorxVT | Typical Contractor |
|---|---|---|
| Root cause failure identification (4-system model) | ✓ | ✗ |
| GPR subsurface mapping + thermal imaging | ✓ | ✗ |
| Measurable trip hazard detection (¼"+) | ✓ | ✗ |
| Legally defensible time-stamped reports | ✓ | ✗ |
| ACI / ASTM / ICRI referenced documentation | ✓ | ✗ |
| Moisture & IR infiltration pathway analysis | ✓ | ✗ |
| AssetGuard™ risk intelligence integration | ✓ | ✗ |
| Failure Correction Strategy (not just surface repair) | ✓ | ✗ |
Residential
$250–$750
Site diagnostic, written condition report, and Failure Correction Strategy recommendation. Full four-system evaluation for driveways, walkways, garage slabs, and residential flatwork.
Commercial
$750–$2,500+
GPR assessment with legally defensible report and full liability documentation. For commercial properties, institutions, municipalities, and insurance claim support.
Portfolio / Municipal
Custom
Multi-property assessment programs with AssetGuard™ platform integration. Ongoing monitoring, prioritized risk scheduling, and portfolio-level risk management.
All work begins with a professional assessment. We don't recommend a Failure Correction Strategy before we understand what's failing — and why it's failing.
We do not perform cosmetic-only corrections or surface patches. Our work is focused on identifying and correcting the underlying cause of failure. If you're looking for the lowest-cost option, we may not be the right fit.
Every project begins with a diagnosis — not a quote. We disqualify projects that don't align with our system before any engagement begins.
If you want a Failure Correction Strategy engineered to the actual failure mode — with documentation, standards references, and a backed guarantee — that's what we do.
Request Professional AssessmentSlabWorxVT operates within a national infrastructure of diagnostic intelligence, vetted contractor networks, and standards platforms. Built for property managers, facility directors, and portfolio operators who need concrete failure intelligence at scale. Municipalities and public infrastructure managers rely on our diagnostic system to protect public assets and reduce liability.
A SlabWorx Platform
concreteassessments.com
Independent diagnostic services with national reach. Standardized assessment methodology, ACI-referenced reporting, and third-party documentation for insurance, litigation, and project planning.
AssetGuard™ by SlabWorx
assetguard.slabworxvt.com
Infrastructure risk intelligence platform. Real-time monitoring, condition tracking, prioritized maintenance scheduling, and portfolio-level concrete asset management for property owners and facility managers.
Vetted Contractor Network
usconcreterepair.com
National vetted contractor network. When diagnostics identify needs outside our direct service area, we connect clients with verified contractors who meet ICRI standards and our diagnostic specifications.
Standards & Authority
nationalconcreterepair.com
Standards and authority platform. ACI, ASTM, and ICRI standards reference library, technical resources, and professional development for diagnostic and Failure Correction practitioners nationwide.
FieldWorx — Field Documentation Tool: Contractors in our network use FieldWorx (field.concreteassessments.com) to document field conditions in real time — site assessment, failure documentation, scope building, and client sign-off, all in one mobile flow.
If the cause isn't corrected, the repair will fail again. Request a professional assessment to get it done correctly the first time.
Describe your concrete failure. We'll review your information and schedule a diagnostic assessment at your property. All projects begin with assessment — no Failure Correction Strategy is recommended without documented findings.
All projects begin with assessment. Complete the form — we review every request before scheduling.
“They told me my driveway needed to be ripped out entirely. SlabWorx ran their diagnostics and showed me exactly which sections were failing and why. We corrected the actual problem. Saved me significantly.”